POE-Detector

POE-Detector

Accessories, Technical Center

Home » Technical Center » Accessories
Welcome to the PoE Texas Manual for the PoE  Detector!

The purpose of the manual is to help you quickly and effectively navigate the  functions of your new Power Over Ethernet Detector.

Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at service@poetexas.com.  Phone +1-512-479-0317.

Or you’re always welcome to leave questions or comments on our product page: POE Detector Tool.

What’s Inside

PARTS LIST:
  • POE DETECTOR

PoE Powered inline device – No batteries necessary

 

Product Features:

 

  • Quickly detect IEEE 802.3af, IEEE 802.3at, 24 Volt Passive and Reverse Polarity Mode B
  • Ergonomic and small for easy carry and use – great for any IT professional
  • Bright LEDs with easy to read indicator chart located on the product
  • PoE Powered inline device – No batteries necessary

NO BATTERIES REQUIRED

SERIOUSLY, NEVER

READING THE DISPLAY

As the display scrolls left, you see in order: volts (V), amps (A), and watts (W)

The display shows only voltage for PoE and DC power supplies if no powered device is connected.  It will “turn on” an IEEE 802.3aft or at PoE port when the “Simulate PoE device” setting is ON and no powered device connected.

The display shows volts, amps, and watts for 802.3af, 802.3at, passive PoE, and DC power supplies when the tester is connected to a powered device.

Mode A or Mode B indicates which wire pairs transmit the power.  See below.

Technical Specifications

Product Specifications

Connector Types Female RJ45
Data Rate N/A
Dimensions 2x1x0.75 in
Mount Type Pocket size
Operating Humidity 5% to 90%
Operating Temperature Range -10 - 60C
PoE Method Powered by PoE
PoE Standard IEEE 802.3af, at, 24 Volt Passive, 48/56 Volt Passive, Reverse Mode B
Power Input Not Required
Weight 0.11 lb

If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!

GAT-IW-Mount

GAT-IW-Mount

Accessories, Technical Center

Home » Technical Center » Accessories

GAT-IW-Mount

Welcome to the PoE Texas Manual for the GAT-IW-Mount, our in-wall mounting accessory for the PoE+ line of splitters and converters.

The purpose of the manual is to help you quickly and effectively navigate the installation of your new Power Over Ethernet Accessory.

Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at success@poetexas.com.  Phone +1-512-479-0317.

Or you’re always welcome to leave questions or comments on our product page: GAT-IW-Mount

What’s Inside

PARTS LIST:

  • 1 X WALL MOUNT BRACKET
  • 1 X MOUNTING TAB
  • 1 X HOLE TEMPLATE CARD

 

GENERAL INSTALLATION

 

Your in-wall mount is designed to install into a wall the same way as a low voltage wall bracket.  So it does require a few tools to install, namely:

 

  • Drywall saw or oscillating tool
  • Pencil
  • Screw driver

First, locate  where you’d like to use the accessory.

Second, use the included card to mark the opening.

Third, cut the opening.

Fourth, set the mount into the opening and use the screw driver to secure it to the wall.

Finally, slide in your GAT device and use the optional mounting tab as necessary.

CONFIGURATION

There is no configuration necessary.  This accessory fits all of our GAT line of products from our PoE to USB-C converters to our PoE to 5 Volt Splitters.

Technical Specifications

Product Specifications

Dimensions 4.25 x 2.6 x 1.75 Inches
Mount Type Inwall 

If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!