AT-LED-24V Installation and Configuration Manual
Welcome to the PoE Texas Manual for the AT-LED-24V, AT-LED-24V-STRIP, AT-LED-24V-DISC, AT-LED-24V-BULB line of products!
The purpose of the manual is to help you quickly and effectively install and configure your new AT-LED-24V kit.
Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at service@poetexas.com. Phone +1-512-479-0317.
Or you’re always welcome to leave questions or comments on our product pages: AT-LED-24V.
What’s Inside
- AT-LED-24V PoE to LED driver
- AT-LED-24V PoE to LED Driver
- 1 x AT-WS-1 Wireless wall switch
- 1 x 2.2m 3200K LED Light Strip
- AT-LED-24V PoE to LED Driver
- 1 x AT-WS-1 Wireless wall switch
- 3 x 2700K LED Light Bulbs
- 2 x wire connectors
- AT-LED-24V PoE to LED Driver
- 1 x AT-WS-1 Wireless wall switch
- 2 x 6500K LED Disc Lights
- 2 x wire connectors
Accessories and Tools
Not Included in Base Kit
- Cat6 Ethernet (2 cables length < 100m)
- Single Gang JBOX or low voltage wall ring
- Wire strippers
DRAWING SETS
Download the Kit Drawing Set
Kit Includes
1 x 2.2m 24V 3200K LED strip
1 x Battery-free Wireless Toggle Light Switch
500 Sqft Space
Kit Includes
2 x 6500K LED Disc lights
1 x Battery-free Wireless Toggle Light Switch
500 Sqft Space
Kit Includes
3 x 2700K LED BULBS
1 x Battery-free Wireless Toggle Light Switch
500 Sqft Space
|
1 x AT-LED-24V 1 x AT-WS-S1 1 x RGB Strip 1 x RGB Controller 1 x RGB Remote |
MOUNTING INSTRUCTIONS
- Before you mount anything, make sure you pair your light switch or multiple light switches with the AT-LED-24V driver. See instructions here.
- If mounting the light switch for flush mounting, identify the light switch mounting location and cut and mount a low voltage ring.
- Otherwise, simply use the adhesive strip to mount the light switch on a wall.
Did you know the light switch will come right out of the mount so you can carry it around?
- The AT-LED-24V can fit into a standard ceiling electrical box, but, as a low voltage device it does not need an enclosure.
- Pull the PoE+ Ethernet line to the mounting location and connect to the AT-LED-24V.
- Now’s a great time to make sure you’ve paired your light switch to the LED drivers you’d like to control.
- Wire up the light fixture or fixtures.
- Test your light switch toggles the lights on/off
Troubleshooting
- My lights don’t turn on:
- Make sure the amber light on the AT-LED-24V is on so you know it’s receiving power
- Double check you have not wired the lights backward. This happens most often with the LED bulb kits
- My lights come on, but they’ll randomly shut off
- Double check you have a PoE+ switch. Ports will drop out if you have a 12 watt PoE switch
- Make sure the total power budget on the PoE switch can support the full load of lights you’ve connected to it. Want to learn more?
- What happens when the power goes off and comes back on again?
- The AT-LED-24V is designed to boot to “on”, so if your lights loose power then they’ll turn on again when power is restored.
PROGRAMMING AND CONFIGURATION
PAIRING LIGHT SWITCH TO DRIVER: Make sure to pair your light switch to the AT-LED-24V after it is powered on but before you install in an enclosure or somewhere inaccessible. The amber LED will be on, and the green LED will start off. Press the AT-LED-24V button for 4-5 seconds. The green light will turn on, then turn off. Once the light is off, the AT-LED-24V is in pairing mode, then press the light switch. When the green led flashes 2 times, it means the pairing has been successful. Each AT-LED-24V can pair with up to 42 switches.
UNPAIRING: Press the AT-LED-24V for 10 seconds, the green LED will turn on, then turn off, then flash 4 times. It means the AT-LED-24V is in factory setting mode. All pairings have been removed.
You may consider doing a preliminary wiring before installing the fixtures to sync the light switch.