GPOES-8-7; POES-8-7

GPOES-8-7; POES-8-7

Switch, Technical Center

Home » Technical Center » Switch

Passive PoE Switches Series Manual for GPOES-8-7 and POES-8-7

Welcome to the Manual for POE Texas Passive POE Switch Series. This series of Switches cost effectively upgrades any non-PoE switch or PoE switch to passive PoE!

The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new Power Over Ethernet Switch.

Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at service@poetexas.com.  Phone +1-512-479-0317.

What’s Inside

GPOES-8-7AB

We do offer this switch with a variety of power supplies so you can select a power supply to fit your application needs.

 

AVAILABLE POWER SUPPLY OPTIONS:

  •  GPOES-8-7AB-56v120w [Includes 56 volt 120 watts Power Supply]
  • GPOES-8-7AB-48v60w-Bundle [Includes 48 volt 60 watt Power Supply]
  • GPOES-8-7AB-48v120w-Bundle [Includes 48 volt 120 watt Power Supply]

Additional items you’ll need not included:

1 – Screws for mounting

2 – Power supply [see available options above]

NEED HELP PICKING A POWER SUPPLY?  USE OUR POE CALCULATOR TO CREATE A POWER BUDGET OR CONTACT A POE-GURU 512-479-0317.

POES-8-7

We also offer this switch with a variety of power supplies so you can select a power supply to fit your application needs.

 

AVAILABLE POWER SUPPLY OPTIONS:

  • POES-8-7-24v60w [Includes 24 volt 60 watts Power Supply]

Additional items you’ll need not included:

1 – Rack Mount screws

2 – Power supply [optional- see available options above]

NEED HELP PICKING A POWER SUPPLY?  USE OUR POE CALCULATOR TO CREATE A POWER BUDGET OR CONTACT A POE-GURU 512-479-0317.

General Installation

GPOES-8-7

Connect the uplink port to your Router or Ethernet switch. Connect the POE ports to your devices – it should power up and connect – and you are all set. The WS-POES-8-7 detects 568A and 568B cabling – so no crossover cables are required. Note below for Power Supply Options

We offer 56, 48, 24, 18 and 12 volt power supplies – if you need a power supply, please call – If your device data sheet shows “48v 350ma” please understand that this is not the power your device needs, but the max power that is available according to the 802.3af spec. For example, a Polycom VOIP phone is 802.3af compatible, but needs about 4 watts to operate. Therefore, one 8 port switch and a 30 watt power supply can power 7 phones with a lower power draw.

POES-8-7

Connect the uplink port to your Router or Ethernet switch. Connect the POE ports to your devices – turn the PoE switch on for ports in use. It should power up and connect – and you are all set. The WS-POES-8-7 detects 568A and 568B cabling – so no crossover cables are required. Note below for Power Supply Options

We offer 56, 48, 24, 18 and 12 volt power supplies – if you need a power supply, please call – If your device data sheet shows “48v 350ma” please understand that this is not the power your device needs, but the max power that is available according to the 802.3af spec. For example, a Polycom VOIP phone is 802.3af compatible, but needs about 4 watts to operate. Therefore, one 8 port switch and a 30 watt power supply can power 7 phones with a lower power draw. 

CONFIGURATION

GPOES-8-7 has configuration switches on the back for PoE: Mode A – Off – Mode B.

Technical Specifications

 GPOES-8-7AB

Product Specifications

Data + PoE Ports 7
Data Ports 1
Data Rate Gigabit
Dimensions 7.5 x 3.25 x 1.25 inches
Input Voltage Range 12-56 Volts DC / 12-56 Volts PoE (Mode B via Uplink)
Max. Amps Per Port 650 mA
Mount Type Wall / Optional 1U Rack POES-RACK-MOUNT (sold separately)
Operating Humidity 5% to 90%
Operating Temperature Range -10 - 60C
PoE Method Passive
PoE Mode/Pinout Mode A (-1,2 +3,6)/Mode B (+4,5 -7,8)
Power Input 2.1 x 5.5 mm DC

 GPOES-8-7AB-56v120w

Product Specifications

Certifications UL/CE/FCC
Data + PoE Ports 7
Data Ports 1
Data Rate Gigabit
Dimensions 7.5 x 3.25 x 1.25 inches
Input voltage 48 Volts
Max Amps Per Kit 2.5 Amps
Max Power for Kit 120 Watts
Max. Amps Per Port 650 mA
Mount Type Wall / Optional 1U Rack POES-RACK-MOUNT (sold separately)
Operating Humidity 5% to 90%
Operating Temperature Range -10 - 60C
Output Voltage 48 volts
PoE Method Passive
PoE Mode/Pinout Mode A (-1,2 +3,6)/Mode B (+4,5 -7,8)
Power Input 2.1 x 5.5 mm DC

 GPOES-8-7AB-24v60w

Product Specifications

Certifications UL/CE/FCC
Data + PoE Ports 7
Data Ports 1
Data Rate Gigabit
Dimensions 7.5 x 3.25 x 1.25 inches
Input voltage 24 Volts
Max Amps Per Kit 2.5 Amps
Max Power for Kit 60 Watts
Max. Amps Per Port 650 mA
Mount Type Wall / Optional 1U Rack POES-RACK-MOUNT (sold separately)
Operating Humidity 5% to 90%
Operating Temperature Range -10 - 60C
Output Voltage 24 Volts
PoE Method Passive
PoE Mode/Pinout Mode A (-1,2 +3,6)/Mode B (+4,5 -7,8)
Power Input 2.1 x 5.5 mm DC

POES-8-7

Product Specifications

Data + PoE Ports 7
Data Ports 1
Data Rate 10/100
Dimensions 7.5 x 3.25 x 1.25 inches
Input Voltage Range 12-56 Volts DC / 12-56 Volts PoE (Mode B via Uplink)
Max. Amps Per Port 650 mA
Mount Type Wall / Optional 1U Rack POES-RACK-MOUNT (sold separately)
Operating Humidity 5% to 90%
Operating Temperature Range -10 - 60C
PoE Method Passive
PoE Mode/Pinout Mode A (-1,2 +3,6)/Mode B (+4,5 -7,8)
Power Input 2.1 x 5.5 mmDC

POES-8-7-24v60w

Product Specifications

Certifications UL/CE/FCC
Data + PoE Ports 7
Data Ports 1
Data Rate 10/100
Dimensions 7.5 x 3.25 x 1.25 inches
Input voltage 24 Volts
Max Power for Kit 60 Watts
Max. Amps Per Port 650 mA
Mount Type Wall / Optional 1U Rack POES-RACK-MOUNT (sold separately)
Operating Humidity 5% to 90%
Operating Temperature Range -10 - 60C
Output Voltage 24 Volts
PoE Method Passive
PoE Mode/Pinout Mode A (-1,2 +3,6)/Mode B (+4,5 -7,8)
Power Input 2.1 x 5.5 mm DC
Power Supplies PS-24v60w; 24 Volt, 1.25 Amp, 60 Watt

If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!

GATS-M L2 Switches

GATS-M L2 Switches

Switch, Technical Center

Home » Technical Center » Switch

Welcome to the PoE Texas Manual for the GATS-M PoE+ Layer 2 Managed Switches!

The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new IEEE 802.3at Layer 2 Managed PoE switch. 

Our goal is to make our products as intuitive and simple to use as possible.  We value your feedback and questions.  You can reach us directly at service@poetexas.com and +1-512-479-0317.

Or you’re always welcome to leave questions or comments on our product pages: GATS-M-TS8200-48P-4FM

What’s Inside

PARTS LIST:GATS-M-TS8200-8P-2FM, GATS-M-TS8200-16P-2FM, GATS-M-24P-4GCM, GATS-M-TS8200-48P-4FM

  • 1 X PoE Switch
  • 1 X Rack Mount Kit – Does NOT include the rack nuts and bolts!

NOTE: The switch includes the screws for the rack wings, but it does not include the rack mounting nuts or screws.  So, you’ll want to grab some of those.

You have everything you need to get your switch up and operating.  Let’s get started.

 

GENERAL INSTALLATION

 

To deploy your new IEEE 802.3at Layer 2 managed switch, you really only need three key things:

  1. 120-240 VAC 50/60 Hz power.
  2. Gigabit Uplink Data on the RJ45 port or Small Form-Factor Pluggable Fibers slot
  3. Space:
  • 1 unit of 19″ rack space
  • 17 1/2″ wide by 9 1/2″ long desk space

* Optional: If you’re rack mounting it, you do need nuts and bolts to mount it on the rack.

Key note:

  • Per UL/IEC 62368-1 Clause F.4, this equipment is intended for use only in a restricted access area.

That’s it!  Let’s get it mounted, then discuss how to configure it.  

Put it together:

RACK MOUNTING:

If you plan to mount this into a rack, simply use the small screws to attach the rack mount wings.  You’ll need a small philips head screwdriver for this.

 The kit does not come with the hardware to mount it to the rack, so don’t forget to pick those up.

CONFIGURATION

The GATS-M will function perfectly as a basic IEEE 802.3at switch for WiFi, IP cameras, or any PoE+ application right out of the box.  For most basic networks, you do not need to configure the switch to operate.  It will power on, negotiate PoE+, enable Spanning Tree Protocol, and forward on the right network traffic for a basic configuration.

However, if you need to configure the switch, you will need a fundamental understanding of networking to do more than a few key management items.  We won’t try to show you how to do all the possible Layer 2 configurations in this manual.  Please contact us if you’d like additional information on configuring Layer 2 settings.

We will cover some important features you can control such as turning on a PoE watchdog, monitoring the ports, and setting your IP address to match your network.

    Configuration Settings

    Configuration Guide Option 1

    Configuration Guide Option 2

    Technical Specifications

    2565Product Specifications

    Data + PoE Ports 8, 16, 24, 48
    Data Ports 2 SFP Gigabit ports or 4 Ports Gigabit + 4 SFP Gigabit Ports
    Data Rate Gigabit
    Data Standard IEEE802.3,IEEE802.3u,IEEE802.3ab, IEEE802.3Z, IEEE802.3X, IEEE 802.3ad, IEEE 802.3q,
    IEEE 802.3q/p, IEEE802.1w, IEEE 802.1D, IEEE 802.1s
    AC Power 120 – 240 VAC, 50/60 Hz
    Total Power 150 watts, 250 watts, 400 watts, 750 watts
    Dimensions

    8 Ports: 210 x 150 x 32 mm

    16 Ports: 440 x 280 x 45 mm

    24 Ports: 440 x 290 x 45 mm

     48 Ports: 440 x 360 x 45 mm
    Display Type Web Management
    Frame Forward Rate 40.32 Mbps
    LEDs Per Port Link/Act (Green), PoE (Orange), Power (Red)
    Management Port Yes
    Mount Type Rack (1U switch)
    Operating Humidity 5% to 95% (non-condensing)
    Operating Temperature Range 0-55 C
    PoE Configurable Per Port Yes
    PoE Mode/Pinout Mode A / B
    PoE Standard IEEE 802.3at
    PoE Standards Supported IEEE 802.3af/at PoE+
    Switching Capacity 20 Gbps, 56 Gbps, 256 Gbps, 512 Gbps

    If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!

    GBT-4-60w

    GBT-4-60w

    Extender, Switch, Technical Center, Technical Center Featured

    Home » Technical Center » Switch

    IEEE 802.3bt PoE Extender Switch

    Welcome to the PoE Texas Manual for the GBT-4-60w!

    The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new PoE Inwall Switch.

    Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at service@poetexas.com.  Phone +1-512-479-0317.

    Or you’re always welcome to leave questions or comments on our product pages: GBT-4-60w.

    What’s Inside

    PARTS LIST: GBT-4-60W

    • 1 x Extender Switch

     

    General Installation

    What you need:

    The GBT-4-60w will power on with any PoE switch, but it will have power budget according to the type of PoE you have:

    • IEEE 802.3af PoE – 12 watts
    • IEEE 802.3at PoE – 25 watts
    • IEEE 802.3bt PoE – 60 watts

    To get the maximum power budget you do need an IEEE802.3bt (single signature, Type 3) switch orinjector.  For example, you can use our GBTS-10-8-55v370w PoE switch.  

    It will function with a Cisco uPoE switch, however it will be limited to a power budget of 25 watts.  

    You can connect any non-PoE, PoE (12 watt), or PoE+ (25 watt) device up to the power budgets listed above based on your PoE switch.

    CONFIGURATION

    There’s nothing to configure.  The GBT-4-60w will automatically network with your infrastructure to receive IP addresses and network protocols.

    Technical Specifications

    Product Specifications

    Certifications FCC, CE, RoHS
    Data + PoE Ports 4
    Data Ports 1
    Data Rate Gigabit
    DC connector 5.5×2.5
    DC Power Input 48-56 VDC
    Dimensions 160*95*22 mm
    Input Voltage 48-56 VDC and PoE
    Input Voltage Range 44-56 volts through Uplink Port
    Installation Wall Mount, Shelf Mount
    LEDs Per Port 2 – Connections and activity
    Max Power for Kit 60 watts total
    Mount Type Wall mount, shelf mount
    Operating Humidity 5% to 90%
    Operating Temperature Range -10 – 45C
    PoE Method IEEE 802.3bt/4PPoE (Uplink) / IEEE 802.3af LAN
    PoE Mode/Pinout Mode A (-1,2 +3,6)/Mode B (+4,5 -7,8)
    PoE Output Power 25 wallts
    PoE Standard Injector: Passive 4 Pair PoE / Switch IEEE 802.3bt and IEEE 802.3af
    PoE Standards Supported IEEE 802.3bt Type 3

    If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!

    GBTS-10-8-M Rev 2

    GBTS-10-8-M Rev 2

    Switch, Technical Center, Technical Center Featured

    Home » Technical Center » Switch

    Welcome to the PoE Texas Manual for the GBTS-10-8-M-V2!

    The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new 8 port IEEE 802.3bt PoE switch designed for Intelligent Lighting and Automation distributed networks. 

    Our goal is to make our products as intuitive and simple to use as possible.  We value your feedback and questions.  You can reach us directly at service@poetexas.com and +1-512-479-0317.

    Or you’re always welcome to leave questions or comments on our product pages: GBTS-10-8-M-V2

    Note: Installation and servicing should be performed by qualified personnel.

    IMPORTANT SAFEGUARDS
    1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.  SAVE THESE INSTRUCTIONS.
    2. Do not use outdoors.
    3. Do not let power supply cords touch hot surfaces.
    4. Do not mount near gas or electric heaters.
    5. The grounding screw is for signal integrity and not for branch safety circuit grounding.
    6. Equipment should be mounted in locations, such as Intermediate Distribution Frames (IDF’s), behind locked doors.
    7. The use of equipment including interconnecting wiring not recommended by the manufacturer may cause an unsafe condition.
    8. Do not use this equipment for other than inteded use.

    SAVE THESE INSTRUCTIONS.

    What’s Inside

    PARTS LIST:GBTS-10-8-M-V2

    • 1 X PoE Switch
    • 1 X Wall Mount Kit
    • 1 X DIN rail Mount Kit – Does not include DIN rail
    • 1 X DC Power Connector
    • 1 X Relay Power Connector

    NOTE: The switch is not Plenum rated per se so PoE Texas kit the switch in a NEMA rated enclosure for mounting in plenum spaces or areas not secured behind a locked door.

    GENERAL INSTALLATION

     

    To deploy your new IEEE 802.3bt DC powered switch, you really only need three key things:

    1. DC power – 42-58 Volts DC, though we recommend 53 volts or higher for Lighting and Automation projects.
    2. Gigabit Uplink Data on the Small Form-Factor Pluggable Fibers slot
    3. Space:
    • Wall Mounted: 6.75″ x  4.5″ (included wall mounting brackets)
    • DIN Rail: 6.5″ x 3.5″ (included DIN rail bracket)
    • NEMA Enclosure: 12″ x 10″ x 6″ (Enclosure Accessory)

    Mounting hardware like screws or wall anchors not included.

    Key note:

    • Per UL/IEC 62368-1 Clause F.4, this equipment is intended for use only in a restricted access area.

    That’s it!  Let’s get it mounted, then discuss how to configure it.  

    About the Power Supply

    The GBTS-10-8-M is designed to take 48-58 volt DC power.  You’ll notice there are two (V1-V2) input power points on the side. Additionally, there is an In (-) and In (+). When wired to the DENT-LINC as an input it can be used for brownout detection (see diagrams below). 

    For One Power Supply (PS) with two outputs: Diagram  

    Connect
    PS V1+ to Switch Input V1+
    PS V1- to Switch Input V1-
    PS V2+ to Switch Input V2+
    PS V2- to Switch Input V2-

     

    For One Power Supply (PS) with one output: Diagram

    Connect
    PS V1+ to Switch Input V1+
    PS V1- to Switch Input V1-
    PS V1+ to Switch Input V2+
    PS V1- to Switch Input V2-

     

    For Two Power Supplies (PS) with two outputs (Note: If using two power supplies, please balance the voltage): Diagram 

    Connect
    PS1 V1+ to Switch Input V1+
    PS1 V1- to Switch Input V1-
    PS2 V1+ to Switch Input V2+
    PS2 V1- to Switch Input V2-

     

    These screw down terminal sockets have are rated for 14 AWG wire.  We recommend crimp on ferrules to make inserting and removing the cable easier.

    The PS-53v3000w power supply designed to operate with this switch comes with interconnecting cables.  You can calculate the correct cable gauge for  your application at the correct distance using our Voltage Drop Calculator.

    If you have questions about how to wire your switch, you can speak to PoE Texas about your cable needs for your project. Additionally, we have installation examples here.

    CONFIGURATION

    The GBTS-10-8-M will function perfectly as a basic IEEE 802.3bt switch for PoE lighting and automation without any configuring right out of the box.  For most basic networks, you do not need to configure the switch to operate.  It will power on, negotiate the 4 Pair PoE for automation, and forward on the right network traffic for a basic configuration.

    However, if you need to configure the switch, you will need a fundamental understanding of networking to do more than a few key management items.  We won’t try to show you how to do all the possible Layer 2 configurations in this manual.  Please contact us if you’d like additional information on configuring Layer 2 settings.

    We will cover some important features you can control such as turning on a PoE watchdog, monitoring the ports, and setting your IP address to match your network.

      CONFIGURATION GUIDE

      Generally, the device comes pre-configured for optimal performance, however, PoE Texas recommends these settings be adjusted:

      • Password – change the password from the default setting
      • Set date/time
      • Name the device per the project nomenclature for identification
      • Optional: Configure VLANs

        Configuration Guide for Emergency Lighting (UL924)

        (PENDING) This PoE switch can be configured for service as a power distribution device for emergency lighting in compliance with UL924.  In order to configure this device for service as an emergency lighting power distribution device, you need to configure it with these parameters in mind:

        • The emergency lightin system must includea UPS backup sized sufficiently so the PoE switch remains powered on during the transfer time from normal to emergency power

        • The PoE switch does not locally store emergency power, so a UL924 rated power transfer and storage device or UL rated back up generator must be provided for 90 minutes of emergency lighting power

        • When used in a UL924 configuration, this PoE switch does not do load shedding so all loads, or lights, connected to that switch must be emergency lights

        • This PoE switch acts simply as a power distribution panel that accepts power from an upstream UL924 transfer device and power storage system and distributes it to downstream lights

        For detailed wiring and configuration information for Emergency Lighting, please see the diagrams below.

         

        Configuration Guide Option 1

        Configuration Guide Option 2

        Configuration Guide for Power Supply PS-53V3000W

        Generally, the device comes pre-configured for optimal performance, however, PoE Texas recommends these settings be adjusted:

        • IP address – the device does not allow for DHCP clients, so a subnet or VLAN should be defined in advance
        • Password – change the password from the default setting
        • Set the date and time
        • Name the device per the project nomenclature for identification
        • Enable/disable batteries as necessary – enable batteries only if one is connected
        • Install and configure temperature probes

         

        Web Management

        CONNECTING TO THE CONSOLE

        The GBTS-28-24-M has a web-based management interface that can be accessed through any of the network ports on the switch.  Before you integrate it into your network, you will need to set the IP address to match your local network settings.

        To start the configuration you need directly connect a network port to a computer.  If you don’t have an ethernet port on your laptop, this works just fine with an ethernet to USB adapter.

        Then power on the injector using any 48-56 volt power supply.  The settings will remain in the device even if you power it off and power it on again.

        Now comes the techiest part of the process.  You will need to disconnect your computer from wifi and the internet.  I know this feels very dangerous, but it’s only for a moment.

        We show the instructions in the video to the left for a Windows computer.  If you need help doing this on a MAC, simply go to YouTube and search on setting an fixed IP address for a MAC.  Then use the IP address information I give below.

        In Windows, navigate to your Network and Sharing Center.  If you don’t know how to get there, simply click on the Window button on the bottom left and type “Network and Sharing Center”.

        When it comes up, you should see an ethernet connection.  If not, double check 1) you’re connected to the switch through an ethernet port, and 2) the switch is powered on.  Click on the ethernet connection.  It will bring up a dialog box.Click “Properties” on the bottom left.

        In the next dialog box, look in the middle for “Internet Protocol Version 4”.  Click on it, then click “Properties” in the bottom right.

        Fill out the fields just like this.

        Click: User the following IP address

        IP Address: 192.168.0.10

        Subnet Mask: Sets itself

        Default Gateway: 192.168.0.5

         

        Preferred DNS Server: 8.8.8.8

        Alternate DNS Server: 4.2.2.2

        Hit Okay to close this dialog, then Okay one more time.

        I’ve tried not hitting okay the second time, and I couldn’t get it to connect.  So, make sure it hit okay to close out the two dialogs.

        Finally, open a web browser and type 192.168.0.1 in the URL Bar.

        The default username is: admin

        The default password is: admin

        You’re in!

        Configuration Settings

        As mentioned above, we’re not going to try to show you how to use all of the functions of a Layer 2 switch, in good part because most of the functions do not really apply to Automation and Lighting.  The video configuration guide shows you how to:

        • Quickly see the status of the ports
        • Log on to the switch
        • Change the basic configurations in terms of time, location, etc.
        • Add or change users
        • Enable/Disable communication to the switch
        • Set the time clock to a server
        • Create a backup configuration file
        • Change the basic IP address of the switch
        • Manage the PoE including setting the total power budget
        • Finally, set a PoE port watchdog to reboot any ports that lose communication

        Technical Specifications

        Product Specifications

        Buffer 4Mbit
        Certifications CE, CB, PFC
        Connector Types Screw In – 20 amp max per connector
        Dimensions 163.2mm×110mm×65.8mm
        Downlink Ports 8*10/100/1000Base-T (PoE)
        ESD Immunity 6KV: Contact discharge 15KV: Air discharge Execute: IEC61000-4-2
        Input Voltage 12-58 VDC
        IP Grade IP40
        Jumbo Frame 10K bytes
        LED Indicator 8*Link/Act (Green), 8*PoE (Orange), 1*PWR (Red)
        MAC Address Table 16K
        Operating Humidity 5%-95% (Non-condensing)
        Operating Temperature -10-55℃
        Packet Forwarding Rate 14.9Mpps
        PoE Line Pair 1/2/4/5(+)，3/6/7/8(-)
        PoE Output Power PoE output power for singe port≤90W, Total PoE power budget≤720W
        PoE Standard 802.3af/at/bt(PSE)
        Power Output 0-10 A, 37-56 VDC, 720 watts
        Standard and Protocols IEEE802.3 , IEEE802.3u, IEEE802.3ab, IEEE802.3Z, IEEE802.3X, IEEE 802.1D, IEEE 802.1af/ at/bt
        Storage Temperature -40-85℃
        Surge Immunity 6KV Execute: IEC61000-4-5
        Switching Capacity 20Gbps / non-blocking
        Uplink Ports 2*1000Base-X SFP Slots

        If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!

        GATS-6-4-52v65w

        GATS-6-4-52v65w

        Switch, Technical Center

        Home » Technical Center » Switch

        Welcome to the PoE Texas Manual for the GATS-6-4-52V65W!

        The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new GATS-6-4-52v65W. 

        Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at service@poetexas.com.  Phone +1-512-479-0317.

        Or you’re always welcome to leave questions or comments on our product pages: GATS-6-4-52v65w.

        What’s Inside

        PARTS LIST:GATS-6-5-52v65w

        • 1 X PoE Switch
        • 1 X AC Cable
        • 1 X Manual

        You have everything you need to get your switch up and operating.  Let’s get started.

         

        GENERAL INSTALLATION

         

        To deploy your new PoE+ or IEEE 802.3at switch, you really only need three key things:

        1. AC power – 120 VAC 60 Hz or 220 VAC 50 Hz – 65 watts
        2. Gigabit Uplink Data on the RJ45 port
        3. Space: 8″ wide by 5″ long desk or wall space

        * Optional: If you’re wall mounting it, you do need screws and wall anchors.

        That’s it!  It’s designed to be a simply, cost effective PoE+ powered switch you can implement quickly.  You don’t need configuration cables, software downloads, apps, or certifications to use it!

         Your switch has four 10/100 PoE ports, two 10/100 Mbps data only ports, and LED indicator lights.  Not a lot to worry about here.  Let’s show you how it goes together.

        Put it together:

        DESK MOUNT:

        If you’re going to set this on a desk or a shelf, you simply place the switch into the location where you need it close enough to the outlet and network connection to your router or switch.

        WALL MOUNT:

        If you plan to mount this on a wall, simply use two wall screws 7.1″ apart to hang the switch on the wall.  You’ll need a small philips head screwdriver for this.

        Now you can plug it in using the included AC cable to power it up.  If you’re grounding your network*, you can use the earthing lug on the back of the switch.*  You might be tempted to overground your network.  Only ground your network in one location and ground it well.  Adding more than one grounding point could actually introduce noise to your network.

        Let’s power this thing on and configure it!

        CONFIGURATION

        Okay, you’re done configuring.  The switch will work right out of the box.

        You can choose to change the settings on all the ports by selecting VLAN, which will create virtual local area networks for each port so that port 1 will not communicate with port 2, etc. for a more secure network.  Or you can choose to “Extend” the range which will allow the PoE ports to communicate up to 10 Mbps up to 250 meters (820 ft).

          LED LIGHTS: All the fun blinky lights!

          What you really want to check for is that the LNK/ACT light is blinking properly.  The LED should blink green indicating communication is happening with your device.

          WIRING

          Technical Specifications

          Product Specifications

          AC Plug Connector Type C14
          Adapters included Yes
          Cable connector length 3 ft
          Certifications CE, FCC, RoHS
          Data + PoE Ports 4
          Data Ports 2 10/100 Mbps
          Data Rate 10/100 Mbps
          Dimensions 8″ x 5″ x 1.325″ in.
          Input Voltage Range 120 / 220 VAC
          LEDs Per Port 1 – PoE, Activity
          Max Power for Kit 65 watts
          Mount Type wall and desk
          Operating Humidity 10% to 90%
          Operating Temperature Range -20 – 50 C
          Output Voltage 52 volts
          PoE Method IEEE 802.3af; IEEE 802.3at
          PoE Mode/Pinout Mode A (-1,2 +3,6)
          PoE Standards Supported IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3az, IEEE802.3x IEEE802.3af, IEEE802.3at
          Storage Temperature -40-80 C

          If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!

          GATS-10-8-51v120w

          GATS-10-8-51v120w

          Switch, Technical Center

          Home » Technical Center » Switch

          Welcome to the PoE Texas Manual for the GATS-10-8-51V120W!

          The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new GATS-10-8-51V120W. 

          Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at service@poetexas.com.  Phone +1-512-479-0317.

          Or you’re always welcome to leave questions or comments on our product pages: GATS-10-8-51v120w

          What’s Inside

          PARTS LIST:GATS-10-8-51V120W

          • 1 X PoE Switch
          • 1 X AC Cable
          • 1 X Manual

          You have everything you need to get your switch up and operating.  Let’s get started.

           

          GENERAL INSTALLATION

           

          To deploy your new PoE+ or IEEE 802.3at switch, you really only need three key things:

          1. AC power – 120 VAC 60 Hz or 220 VAC 50 Hz – 500 watts
          2. Gigabit Uplink Data on the RJ45 port
          3. Space: 8 3/4″ wide by 6 1/2″ long desk or wall space

          That’s it!  It’s designed to be a simply, cost effective PoE+ powered switch you can implement quickly.  You don’t need configuration cables, software downloads, apps, or certifications to use it!

           Your switch has eight Gigabit PoE ports, two Gigabit data only ports, and LED indicator lights.  Not a lot to worry about here.  Let’s show you how it goes together.

          Put it together:

          DESK MOUNT:

          If you’re going to set this on a desk or a shelf, you simply place the switch into the location where you need it close enough to the outlet and network connection to your router or switch.

          Now you can plug it in using the included AC cable to power it up.  If you’re grounding your network*, you can use the earthing lug on the back of the switch.*  You might be tempted to overground your network.  Only ground your network in one location and ground it well.  Adding more than one grounding point could actually introduce noise to your network.

          Let’s power this thing on and configure it!

          CONFIGURATION

          Okay, you’re done configuring.  The switch will work right out of the box.

            LED LIGHTS: All the fun blinky lights!

            What you really want to check for is that the LNK/ACT light is blinking properly.  The LED should blink green indicating communication is happening with your device.

            WIRING

            Technical Specifications

            Product Specifications

            AC Plug Connector Type C14
            Adapters included Yes
            Cable connector length 3 ft
            Certifications CE, FCC, RoHS
            Data + PoE Ports 8
            Data Ports 2 Gigabit
            Data Rate Gigabit
            Dimensions 8.74″ x 6.5″ x 1.325″ in.
            Input Voltage Range 120 / 220 VAC
            LEDs Per Port 1 – PoE, Activity
            Max Power for Kit 120 watts
            Mount Type Desk
            Operating Humidity 10% to 90%
            Operating Temperature Range -20 – 50 C
            Output Voltage 51 volts
            PoE Method IEEE 802.3af; IEEE 802.3at
            PoE Mode/Pinout Mode A (-1,2 +3,6)
            PoE Standards Supported IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3az, IEEE802.3x
            IEEE802.3af, IEEE802.3at
            Storage Temperature -40-80 C

            If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!

            GBTS-28-24-M

            GBTS-28-24-M

            Switch, Technical Center

            Home » Technical Center » Switch

            Welcome to the PoE Texas Manual for the GBTS-28-24-M!

            The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new 24 port IEEE 802.3bt PoE switch designed for Intelligent Lighting and Automation. 

            Our goal is to make our products as intuitive and simple to use as possible.  We value your feedback and questions.  You can reach us directly at service@poetexas.com and +1-512-479-0317.

            Or you’re always welcome to leave questions or comments on our product pages: GBTS-28-24-M

            Note: Installation and servicing should be performed by qualified personnel.

            IMPORTANT SAFEGUARDS
            1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.  SAVE THESE INSTRUCTIONS.
            2. Do not use outdoors.
            3. Do not let power supply cords touch hot surfaces.
            4. Do not mount near gas or electric heaters.
            5. The grounding screw is for signal integrity and not for branch safety circuit grounding.
            6. Equipment should be mounted in locations, such as Intermediate Distribution Frames (IDF’s), behind locked doors.
            7. The use of equipment including interconnecting wiring not recommended by the manufacturer may cause an unsafe condition.
            8. Do not use this equipment for other than inteded use.

            SAVE THESE INSTRUCTIONS.

            What’s Inside

            PARTS LIST:GBTS-28-24-M

            • 1 X PoE Switch
            • 1 X Rack Mount Kit – Does NOT include the rack nuts and bolts!

            NOTE: The switch includes the screws for the rack wings, but it does not include the rack mounting nuts or screws.  So, you’ll want to grab some of those.

            You will want to have patch cables and potential some ferrule connectors for the power cables on hand if you’re not using the cables supplied with our PS-53v3000w power rectifier.

            You have everything you need to get your switch up and operating.  Let’s get started.

             

            GENERAL INSTALLATION

             

            To deploy your new IEEE 802.3bt DC powered switch, you really only need three key things:

            1. DC power – 42-58 Volts DC, though we recommend 53 volts or higher for Lighting and Automation projects.
            2. Gigabit Uplink Data on the RJ45 port or Small Form-Factor Pluggable Fibers slot
            3. Space:
            • 1 unit of 19″ rack space
            • 17 1/2″ wide by 9 1/2″ long desk space

            * Optional: If you’re rack mounting it, you do need nuts and bolts to mount it on the rack.

            Key note:

            • Per UL/IEC 62368-1 Clause F.4, this equipment is intended for use only in a restricted access area.

            That’s it!  Let’s get it mounted, then discuss how to configure it.  

            Put it together:

            RACK MOUNTING:

            If you plan to mount this into a rack, simply use the small screws to attach the rack mount wings.  You’ll need a small philips head screwdriver for this.

             The kit does not come with the hardware to mount it to the rack, so don’t forget to pick those up.

            About the Power Supply

            The GBTS-28-24-M is designed to take 48-58 volt DC power.  You’ll notice there are two input power points on the back.  

            The switch operates at maximum power output when both terminals are connected to the power supply.

            These push-in terminal sockets have a 22.5 amp limit and are rated for 10 AWG wire.  We recommend crimp on ferrules to make inserting and removing the cable easier.

            The PS-53v3000w power supply designed to operate with this switch comes with interconnecting cables.  You can use 1 x set of 12 gauge wire to power up to 1080 watts.  As you go up above 1080 watts in total power draw, you will need to use the second power port or V2. 

            If you have specific cable needs beyond the included interconnecting cables, you can speak to PoE Texas about your cable needs for your project.

            HOW DO I KNOW HOW BIG MY POWER SUPPLY SHOULD BE?

            You can use our PoE calculator to quickly calculate your expected load on the PoE injector.

            Check it out here:

            PoE Calculator

            WIRING DIAGRAMS FOR

            GBTS-28-24-M AND PS-53V3000W POWER RECTIFIER

            Download Drawings

             

            CONFIGURATION

            The GBTS-28-24-M will function perfectly as a basic IEEE 802.3bt switch for PoE lighting and automation without any configuring right out of the box.  For most basic networks, you do not need to configure the switch to operate.  It will power on, negotiate the 4 Pair PoE for automation, and forward on the right network traffic for a basic configuration.

            However, if you need to configure the switch, you will need a fundamental understanding of networking to do more than a few key management items.  We won’t try to show you how to do all the possible Layer 2 configurations in this manual.  Please contact us if you’d like additional information on configuring Layer 2 settings.

            We will cover some important features you can control such as turning on a PoE watchdog, monitoring the ports, and setting your IP address to match your network.

              CONFIGURATION GUIDE

              Generally, the device comes pre-configured for optimal performance, however, PoE Texas recommends these settings be adjusted:

              • Password – change the password from the default setting
              • Set date/time
              • Name the device per the project nomenclature for identification
              • Optional: Configure VLANs

                Configuration Guide for Emergency Lighting (UL924)

                (PENDING) This PoE switch can be configured for service as a power distribution device for emergency lighting in compliance with UL924.  In order to configure this device for service as an emergency lighting power distribution device, you need to configure it with these parameters in mind:

                • The emergency lightin system must includea UPS backup sized sufficiently so the PoE switch remains powered on during the transfer time from normal to emergency power

                • The PoE switch does not locally store emergency power, so a UL924 rated power transfer and storage device or UL rated back up generator must be provided for 90 minutes of emergency lighting power

                • When used in a UL924 configuration, this PoE switch does not do load shedding so all loads, or lights, connected to that switch must be emergency lights

                • This PoE switch acts simply as a power distribution panel that accepts power from an upstream UL924 transfer device and power storage system and distributes it to downstream lights

                For detailed wiring and configuration information for Emergency Lighting, please see the diagrams below.

                 

                Configuration Guide Option 1

                Configuration Guide Option 2

                Configuration Guide for Power Supply PS-53V3000W

                Generally, the device comes pre-configured for optimal performance, however, PoE Texas recommends these settings be adjusted:

                • IP address – the device does not allow for DHCP clients, so a subnet or VLAN should be defined in advance
                • Password – change the password from the default setting
                • Set the date and time
                • Name the device per the project nomenclature for identification
                • Enable/disable batteries as necessary – enable batteries only if one is connected
                • Install and configure temperature probes

                 

                Web Management

                CONNECTING TO THE CONSOLE

                The GBTS-28-24-M has a web-based management interface that can be accessed through any of the network ports on the switch.  Before you integrate it into your network, you will need to set the IP address to match your local network settings.

                To start the configuration you need directly connect a network port to a computer.  If you don’t have an ethernet port on your laptop, this works just fine with an ethernet to USB adapter.

                Then power on the injector using any 48-56 volt power supply.  The settings will remain in the device even if you power it off and power it on again.

                Now comes the techiest part of the process.  You will need to disconnect your computer from wifi and the internet.  I know this feels very dangerous, but it’s only for a moment.

                We show the instructions in the video to the left for a Windows computer.  If you need help doing this on a MAC, simply go to YouTube and search on setting an fixed IP address for a MAC.  Then use the IP address information I give below.

                In Windows, navigate to your Network and Sharing Center.  If you don’t know how to get there, simply click on the Window button on the bottom left and type “Network and Sharing Center”.

                When it comes up, you should see an ethernet connection.  If not, double check 1) you’re connected to the switch through an ethernet port, and 2) the switch is powered on.  Click on the ethernet connection.  It will bring up a dialog box.Click “Properties” on the bottom left.

                In the next dialog box, look in the middle for “Internet Protocol Version 4”.  Click on it, then click “Properties” in the bottom right.

                Fill out the fields just like this.

                Click: User the following IP address

                IP Address: 192.168.0.10

                Subnet Mask: Sets itself

                Default Gateway: 192.168.0.5

                 

                Preferred DNS Server: 8.8.8.8

                Alternate DNS Server: 4.2.2.2

                Hit Okay to close this dialog, then Okay one more time.

                I’ve tried not hitting okay the second time, and I couldn’t get it to connect.  So, make sure it hit okay to close out the two dialogs.

                Finally, open a web browser and type 192.168.0.1 in the URL Bar.

                The default username is: admin

                The default password is: admin

                You’re in!

                Configuration Settings

                As mentioned above, we’re not going to try to show you how to use all of the functions of a Layer 2 switch, in good part because most of the functions do not really apply to Automation and Lighting.  The video configuration guide shows you how to:

                • Quickly see the status of the ports
                • Log on to the switch
                • Change the basic configurations in terms of time, location, etc.
                • Add or change users
                • Enable/Disable communication to the switch
                • Set the time clock to a server
                • Create a backup configuration file
                • Change the basic IP address of the switch
                • Manage the PoE including setting the total power budget
                • Finally, set a PoE port watchdog to reboot any ports that lose communication

                Heat Load Calculator

                The GBTS-28-24-M does put off enough heat when under load that it’s important to consider how you will deal with the heat.  The key considerations are:

                • The GBTS-28-24-M operates well up to 40 C or 104 F in local ambient conditions
                • Local ambient conditions mean the space where the switch will be located
                • While an office space may be at 75 F, a fully enclosed rack without ventilation can easily go above 110 F
                • Ideally the GBTS-28-24-M is installed in the rack with at least 1u space between it and the PS-53V3000W
                • Racks should either be open in the back or have good, reliable forced ventilation to move around around and out of the cabinet
                • The room outside, typically an IDF or MDF, the rack or cabinet should have local temperature control through a thermostat and air handling unit
                • See the Heat Load Calculator to see how to size any air handling or air conditioning requirements

                To estimate the heat load of the PS-53v3000w power supply, visit that Heat Load Calculator.

                Management of heat for your equipment is an essential element to the life expectancy of your equipment.  Overheating when using these switches at full load is a possibility.  Our best practices for a rack configuration are:

                1. Provide at least 1u space between switches to allow for air flow.
                2. Include rack mounted vent fans to provide for good air circulation.  We have often seen this brand used: https://rackfans.com/
                3. Do not mount the equipment in enclosed racks that have poor air circulation.

                Technical Specifications

                Product Specifications

                Data + PoE Ports 24
                Data Ports 4 Ports Gigabit + 4 SFP Gigabit Ports
                Data Rate Gigabit
                Data Standard IEEE802.3,IEEE802.3u,IEEE802.3ab, IEEE802.3Z, IEEE802.3X, IEEE 802.3ad, IEEE 802.3q,
                IEEE 802.3q/p, IEEE802.1w, IEEE 802.1D, IEEE 802.1s
                DC connector Push In Connector
                DC Power Input 2,160 Watts
                Dimensions Switch: 19 x 3.5 x 1.5 inches / Rectifier: 19 x 13.25 x 1.75 inches
                Display Type Web Management
                Frame Forward Rate 40.32 Mbps
                Input voltage 55 Volts DC
                Input Voltage Range 48 – 55 Volts DC
                LEDs Per Port Link/Act (Green), PoE (Orange), Power (Red)
                Management Port Yes
                Max Power for Kit 2160 Watts
                Max Voltage 58 Volts
                Max. Amps Per Port 90 watts
                Mount Type Rack (1U switch + 1U Rectifier)
                Operating Humidity 5% to 95% (non-condensing)
                Operating Temperature Range -10-55 C
                PoE Configurable Per Port Yes
                PoE Mode/Pinout Mode A / B
                PoE Standard IEEE 802.3bt Type 3;
                4 Pair PoE;
                Mode A / B negotiation
                PoE Standards Supported IEEE 802.3af/at/bt Type 3/bt Type4
                4 Pair PoE;
                Power Supplies Optional 55v 3000w Rectifier [GBT-24-M-56v3000w]
                Switching Capacity 128 G
                Weight Switch Only: 4.5 lbs; Switch + Power Supply: 17.75 lbs

                If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!

                GPOES-24-2-55v390w

                GPOES-24-2-55v390w

                Switch, Technical Center

                Home » Technical Center » Switch

                GPOES-24-2-55v390w

                Welcome to the PoE Texas Manual for the 24 port LCD Managed PoE switch!

                The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new Power Over Ethernet Switch.

                Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at service@poetexas.com. Phone +1-512-479-0317.

                Or you’re always welcome to leave questions or comments on our product page: GPOES-24-2-55v390w.

                What’s Inside

                PARTS LIST:

                • 1 X POE SWITCH
                • 1 X USER GUIDE
                • 1 X POWER CORD
                • 2 X RACK MOUNT BRACKETS
                • 8 X SCREWS (FOR RACK MOUNT)
                • 4 X RUBBER ADHESIVE FEET

                General Installation

                Your new PoE switch is designed to be simple to install and set up. You should only need at most a Philips head screw driver. To power it on, plug the power cable in the back.

                Since this is an IEEE 802.3at (PoE+), you can just start plugging devices into it to eight PoE ports on the left hand side marked 1 through 24.

                Ports 25S and 26S are for Small Form-factor Pluggable (SFP) fiber optic ports. There are two of them to allow you to create a self-healing ring network.  If you’re just using Ethernet, you can use ports 23 and 4 for the same purpose.

                Desktop Installation

                STEPS:

                1. Remove the adhesive backs from the rubber feet accessories and place them on the bottom of the housing in the square indentations for these
                2. Plug the switch into an outlet
                3. Start plugging in your PoE and non-PoE devices

                *The rubber feet help the switch have the proper ventilation, so please don’t skip that step.
                Yeah, it is that simple.

                Rack Installations

                The switch comes with brackets for a 19″ rack configuration.  Please contact us if you need a different rack.  It DOES NOT come with the nuts and screws to mount the switch onto the rack.  You’ll need to get those

                STEPS:

                1. Using the 8 x small screws provided in the box, attach the two rack brackets to either side of the switch so that the brackets face the front as in the image above
                2. Using rack screws and nuts (not provided) mount the switch into the rack space (the switch will use 1u of rack space)
                3. Plug the switch into an outlet
                4. Start plugging in your PoE and non-PoE devices

                Operating The LCD Screen

                Main Display

                When you plug in the PoE switch, it will automatically boot up to the PoE Texas screen. Then, the main monitoring screen will come up. This screen gives you a great heads up display on the PoE situation with the whole switch.

                So why make a PoE switch with a display like this rather than just a managed switch? We’re considering the smart building situations where networks and infrastructure aren’t always in place when you need to start installing and testing new PoE devices such as lighting, displays, or sensors. This display screen allows a user to see and manage the PoE on devices without having to have the full network installed and turned up.

                So what does it all mean?

                First Column: This identifies the port numbers, including the two uplink ports 9 and 10

                Second Column: The power status of the port.  See guide to terms below.

                Third Column: The entering data rate from the device used on the port (in Mbps)

                Fourth Column: The exiting data rate from the device (in Mbps)

                If the data rate turns red, then the port is exceeding its bandwidth settings.

                PB: The maximum power available on the switch

                TP: The current output power of the entire switch

                PD: The number of powered devices connected to the switch

                Norm: The switch configuration mode.

                Options: (Norm – Normal switch; VLAN – All ports have their own VLAN; CCTV – CCTV camera set up.  See section on Menu item 1 Switch Mode)

                What Do the Codes In Column 1 Mean?

                —-W: Nothing is drawing power on this port
                OLP: Over load protection has triggered on this port, meaning you device is drawing too much power for the port (see section on Port Power).
                ULP: Under load protection has triggered on this port, meaning the device is drawing too little power to keep the PoE live on the port.
                SCP: Short Circuit Protection, meaning the device or the cable connected to this port has short circuited. You’ll need to replace somethings.
                OFF: When green or white, the port has been set to “off” in the settings
                When red, the data rate used by this port exceeds the set max. If this happens 10 times in 1 hour, the port will power down to protect the switch and other devices.

                Switch Bandwidth

                Switch Bandwidth allows you to limit how much of the switch’s bandwidth a particular port can use.  Let’s say you’re worried some guy will mine crypto currency through this switch.  You can set the switch to alert you here that a single port is taking more bandwidth than the setting.

                PD Type

                PD Type gives you control to override the Powered Device negotiation on the switch.
                • Standard: Your devices will negotiate the type of PoE and the classification
                • Enhance: Regardless of the device negotiation, this setting allows the port to deliver up to AT power and the settings you put in the PSE Port Power
                • Legacy: Not used very frequently, this allows the switch to negotiate with a capacitance tag Powered Device
                Unless you have a specific application or some unusual devices, you’ll likely just keep it on Standard.

                PD Alive

                PD Alive lets you set up an automatic reboot function for a port. Let’s say you have a security camera on the port, and it stops communicating for whatever reason. This feature here allows the PoE switch to take over and reboot the port to see if the device will come back on.

                Use the up and down arrows to navigate to the port you want to have this feature on. Press “Enter” until the “Disable” is green. Then, press “Up” or “Down” until you see “Enable”.

                Then press “Enter” again to set up the Start Up time using the up/down buttons: how long in seconds the device should take to start up.

                 

                Then “Enter” again to set the Interval time using the up/down buttons: how long in seconds the switch should wait to see if the device comes back up again.

                Then “Enter” one last time to set the PowerOff time using the up/down bottons: how long it should stay off when it turns off.

                When you’re done, use the “Back” button multiple times to exit to the main menu.

                PSE Power Fine

                PSE Power Fine allows you to adjust the residual power output of the ports so they can output more power as long as you have enough Total Power Budget (TB). This is used in some specific applications where you know your devices are riding right at the 25 watt limits of PoE+, say with a PTZ camera or a large Wifi access point (some of the high performance Cisco WAP’s fall into this category if their USB ports are turned on).

                Depending on your situation you can add 5%, 10%, and 15% to the Power Budget (PB).

                Use the up and down arrow buttons to select the option preferred, then use the “Enter” button to select it.  When the < is next to the setting and green, your option is selected.  “Back” out to the main menu.

                PSE Port Priority

                PSE Port Priority sets the priority for which ports will pull more power if the Power Budget (PB) of all the ports exceeds the Total Power Budget (TB) at any time.

                Let’s say you have security cameras, phones, and wifi access points on your switch, and you’re right at the TB of the switch. If you want to make sure your security cameras stay live even if one of the wifi access points start to draw too much power, then the switch will prioritize the ports based on these settings.

                By default, the lower number ports (1, 2, 3 . . . ) are higher priority. If you set both ports 1 and 2 at “High” priority, then port 1 will prioritize over port 2 in case of a conflict.

                With the port numbers highlighted green, use the up and down buttons to select the port number.  Select “Enter”.  Then, use the up and down buttons to select the priority.  You have selected one when it is green and has the < next to is.  Then “Back” to the main menu.

                PSE Port Enable

                PSE Port Enable give you the control to be able to turn on and off the power on any port. This ideal for infrastructure or IOT situations where the network may not be turned up for some time but the devices need to be installed, powered on, and tested during installation.

                With the port number green, use the up and down buttons to select a port number. Then, press “Enter”. Use the up and down buttons until the “Enable” or “Disable” is green. Then press enter.

                “Back” to the main menu.

                PSE Port Power

                PSE Port Power gives you control of whether a port can run at higher power than the traditional PoE standard. For example, you have a Thinlabs all-in-one PoE computer that you know you’ll use hard and add a lot of USB devices to. Rather than worry about your power budget, you can increase your power limit all the way up to 36 watts. Or, if you know your device will be small and you want to save on your PB, you can set the power consumption as low as 2 watts.

                As before, while the port number is green, use the up and down buttons to select a port. Then press “Enter”. With the power green, use the up and down arrows to set the power limit on the port. “Back” to the main menu.

                Note: This function is different from the PSE Power Fine function because that sets the fine auto adjustments, while PSE Port Power lets you set the big ranges.

                In order to take full advantage of the PSE Port Power feature, you need to make sure the switch is set to “Enhanced” on the PD Type menu.  Otherwise you’ll receive this error.

                LCD On/Off

                LCD ON/OFF gives you control over how long the LCD screen will remain active after the last use.

                Simply use the up and down buttons to select your setting, then press “Enter”. The selected setting will turn green and be immediately ready to use. Press “Back” to get to the main menu.

                Fan Control

                Fan Control gives you control of when the cooling fans will turn on. It’s based on the percent of the Power Budget (PB) used at the time. This allows you to keep the switch quiet until heat demands force it on.

                Caution, though, setting the value too high in a warm environment like a packed server rack could allow the switch to go above the rated temperature limits.

                Simply use the up and down buttons to select your setting, then press “Enter”. The selected setting will turn green and be immediately ready to use. Press “Back” to get to the main menu.

                Language

                You can select your Language on this menu.  Currently, Chinese and English are available.  Other languages can be added by request.

                Simply use the up and down buttons to select your setting, then press “Enter”.  The selected setting will turn green and be immediately ready to use.  Press “Back” to get to the main menu.

                Default Setting

                DEFAULT SETTING restores the switch to factory default settings.  

                Simply use the up and down buttons to select “Confirm”, then press “Enter”.  The selected setting will turn green and be immediately ready to use.  Press “Back” to get to the main menu.

                About

                The About menu gives you diagnostic information about model and software version of your device.

                Technical Specifications

                AC Plug Connector Type C14
                Adapters included Yes
                Cable connector length 3 ft
                Certifications CE, FCC,
                Data + PoE Ports 24
                Data Ports 2 SPF
                Data Rate Gigabit
                Dimensions 17.32″ x 9.133″ x 1.77″ in.
                Display Type Bright LCD
                Input Voltage Range 120 / 220 VAC
                LEDs Per Port 1 – Connections and activity
                Max Power for Kit 390 watts
                Mount Type wall and rack (accessories included)
                Operating Humidity 10% to 90%
                Operating Temperature Range 0 – 40 C
                Output Voltage 55 volts
                PoE Method IEEE 802.3af; IEEE 802.3at
                PoE Mode/Pinout Mode A (-1,2 +3,6)/Mode B (+4,5 -7,8)
                PoE Standards Supported IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3az, IEEE802.3x IEEE802.3af, IEEE802.3at

                If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!

                GBTS-10-8-55V370W Manual

                GBTS-10-8-55V370W Manual

                Switch, Technical Center, Technical Center Featured

                Home » Technical Center » Switch

                Welcome to the PoE Texas Manual for the GBTS-10-8-55V370W!

                 The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new GBTS-10-8-55V370W. 

                 Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at service@poetexas.com.  Phone +1-512-479-0317.

                 Or you’re always welcome to leave questions or comments on our product pages: GBTS-10-8-55V370W

                What’s Inside

                PARTS LIST:GBTS-10-8-55V370W

                • 1 X PoE Switch
                • 1 X Rack Mount Kit – Does NOT include the rack nuts and bolts!
                • 4 X Desk Mount Rubber Pads
                • 1 X AC Cable

                 

                You have everything you need to get your switch up and operating.  Let’s get started.

                 

                GENERAL INSTALLATION

                 

                To deploy your new uPoE or IEEE 802.3bt switch, you really only need three key things:

                1. AC power – 120 VAC 60 Hz or 220 VAC 50 Hz – 500 watts
                2. Gigabit Uplink Data on the RJ45 por or Small Form-Factor Pluggable Fibers slot
                3. Space:
                • 1 unit of 19″ rack space
                • 17 1/2″ wide by 9 1/2″ long desk space

                 * Optional: If you’re rack mounting it, you do need nuts and bolts to mount it on the rack.

                That’s it!  It’s designed to be a simply, cost effective, high powered switch you can implement quickly.  You don’t need configuration cables, software downloads, apps, or certifications to use it!

                 

                Your switch has eight Gigabit PoE ports, two Gigabit data only ports, two SFP slots, and an LCD status display.  Not a lot to worry about here.  Let’s show you how it goes together.

                Put it together:

                DESK MOUNT:

                If you’re going to set this on a desk or a shelf, you simply stick the included rubber feet on to the bottom of the switch in the small square indentations provided.  You don’t have to screw on the rack wings unless you just like the look of them.

                RACK MOUNT:

                If you plan to mount this into a rack, simply use the small screws to attach the rack mount wings.  You’ll need a small philips head screwdriver for this.

                 

                The kit does not come with the hardware to mount it to the rack, so don’t forget to pick those up.

                Now you can plug it in using the included AC cable to power it up.If you’re grounding your network*, you can use the earthing lug on the back of the switch.* You might be tempted to overground your network.  Only ground your network in one location and ground it well.  Adding more than one grounding point could actually introduce noise to your network.gs.

                Let’s power this thing on and configure it!

                CONFIGURATION

                Okay, I told you there wouldn’t be any configuration.  I lied.  You do have to pick whether your network needs IEEE 802.3bt Type 4 PoE or uPoE.  There’s a table down below that will layout the technical details, but here’s what you really need to know:

                IEEE 802.3bt will be compatible with newer, higher power devices that say IEEE 802.3bt.

                uPOE will be compatible with pre-standard devices that typically say PoE++ or UPOE.

                 

                I tell you this now so you can decide before you start connecting your devices.  All you need to do is slide the selector switch to the type of PoE you’d like.  See, not so bad afterall.

                  ON THE LCD SCREEN:

                  The LCD screen will tell you a lot about what’s going on really quickly with your network.  You can:

                  • See how much power your device is drawing or whether it’s on or off
                  • If your device is having an issue because of underloading*, overloading, or a short circuit
                  • What your total output power is and what your power budget is

                   

                  *Underloading is a condition where your PoE device isn’t drawing enough power to keep the PoE on.   If you’re using a PoE splitter, you can try plugging a device into to start drawing power.  Otherwise, contact us at service@poetexas.com for support.

                  LED LIGHTS: All the fun blinky lights!

                  The table here shows all the details.  What you really want to check for is that the only light blinking is the LNK/ACT lights.  If other lights are blinking, you have an issue.

                  Technical Specifications

                  Product Specifications

                  AC Plug Connector Type C14
                  Data + PoE Ports 8
                  Data Ports 4 (2-Gigabit and 2-SPF)
                  Data Rate Gigabit
                  Display Type LED
                  Input voltage 110 – 220 VAC
                  Max Power for Kit 370 Watts
                  Max Voltage 55 Volts
                  Mount Type 1U Rack Mount
                  Operating Humidity 10% to 90%
                  Operating Temperature Range 0-40 C
                  Output Voltage 55 Volts
                  PoE Method IEEE 802.3bt
                  PoE Standard IEEE 802.3bt
                  PoE Standards Supported uPoE, IEEE 802.3bt

                  If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!

                  GBT-4-IW

                  GBT-4-IW

                  Switch, Technical Center, Technical Center Featured

                  Home » Technical Center » Switch

                  IEEE 802.3bt PoE Inwall Switch

                  Welcome to the PoE Texas Manual for the GBT-4-IW!

                  The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new PoE Inwall Switch. 

                  Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at service@poetexas.com.  Phone +1-512-479-0317.

                  Or you’re always welcome to leave questions or comments on our product pages: GBT-4-IW.

                  What’s Inside

                  PARTS LIST: GBT-4-IW

                  • 1 X Inwall Switch
                  • 2 X Screws for mounting into gang box
                  • 1 X front cover plate

                  **It does not include a gang box.

                  General Installation

                  What you need:

                  The GBT-4-IW will power on with any PoE switch, but it will have power budget according to the type of PoE you have:

                  • IEEE 802.3af PoE – 12 watts
                  • IEEE 802.3at PoE – 25 watts
                  • IEEE 802.3bt PoE – 60 watts

                  To get the maximum power budget you do need an IEEE802.3bt (single signature, Type 4) switch orinjector.  For example, you can use our GBTS-10-8-55v370w PoE switch.  

                  It will function with a Cisco uPoE switch, however it will be limited to a power budget of 25 watts.  

                  Put it together:

                  You can connect any non-PoE, PoE (12 watt), or PoE+ (25 watt) device up to the power budgets listed above based on your PoE switch.

                  CONFIGURATION

                  There’s nothing to configure.  The GBT-4-IW will automatically network with your infrastructure to receive IP addresses and network protocols.

                  Technical Specifications

                  Product Specifications

                  Certifications CE, FCC, RoHS
                  Data + PoE Ports 4
                  Data Ports 1
                  Data Rate Gigabit
                  Dimensions Single Gang US Box
                  Display Type Blue LED Status Indicator
                  Input Voltage Range 44-56 volts through Uplink Port
                  Max Power for Kit 60 watts total
                  Mount Type In-wall
                  Operating Humidity 5% to 90%
                  Operating Temperature Range -10 – 45C
                  PoE Method IEEE 802.3bt/4PPoE (Uplink) / IEEE 802.3af LAN
                  PoE Mode/Pinout Mode A (-1,2 +3,6)/Mode B (+4,5 -7,8)
                  PoE Standard Injector: Passive 4 Pair PoE / Switch IEEE 802.3bt and IEEE 802.3af
                  PoE Standards Supported Single Signature IEEE 802.3bt Type 4

                  If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!

                  GPOE-10-8-55V130W

                  GPOE-10-8-55V130W

                  Switch, Technical Center

                  Home » Technical Center » Switch

                  GPOES-10-8-55v130w

                  Welcome to the PoE Texas Manual for the 8 port LCD Managed PoE switch!

                  The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new Power Over Ethernet Switch.

                  Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at service@poetexas.com. Phone +1-512-479-0317.

                  Or you’re always welcome to leave questions or comments on our product page: GPOES-10-8-55v130w.

                  What’s Inside

                  PARTS LIST:

                  • 1 X POE SWITCH
                  • 1 X USER GUIDE
                  • 1 X POWER CORD
                  • 2 X RACK MOUNT BRACKETS
                  • 8 X SCREWS (FOR RACK MOUNT)
                  • 4 X RUBBER ADHESIVE FEET

                  General Installation

                  Your new PoE switch is designed to be simple to install and set up. You should only need at most a Philips head screw driver. To power it on, plug the power cable in the back.

                  Since this is an IEEE 802.3at (PoE+), you can just start plugging devices into it to eight PoE ports on the left hand side marked 1 through 8.

                  Ports 9T and 10T are the Gigabit uplink ports where you connect back to your router or main network switch. Ports 9S and 10S are for Small Form-factor Pluggable (SFP) fiber optic ports. If you’re not familiar with fiber optic connections, you can leave the little plastic plugs installed.

                  Desktop Installation

                  STEPS:

                  1. Remove the adhesive backs from the rubber feet accessories and place them on the bottom of the housing in the square indentations for these
                  2. Plug the switch into an outlet
                  3. Start plugging in your PoE and non-PoE devices

                  *The rubber feet help the switch have the proper ventilation, so please don’t skip that step.
                  Yeah, it is that simple.

                  Rack Installations

                  The switch comes with brackets for a 19″ rack configuration.  Please contact us if you need a different rack.  It DOES NOT come with the nuts and screws to mount the switch onto the rack.  You’ll need to get those

                  STEPS:

                  1. Using the 8 x small screws provided in the box, attach the two rack brackets to either side of the switch so that the brackets face the front as in the image above
                  2. Using rack screws and nuts (not provided) mount the switch into the rack space (the switch will use 1u of rack space)
                  3. Plug the switch into an outlet
                  4. Start plugging in your PoE and non-PoE devices

                  Operating The LCD Screen

                  Main Display

                  When you plug in the PoE switch, it will automatically boot up to the PoE Texas screen. Then, the main monitoring screen will come up. This screen gives you a great heads up display on the PoE situation with the whole switch.

                  So why make a PoE switch with a display like this rather than just a managed switch? We’re considering the smart building situations where networks and infrastructure aren’t always in place when you need to start installing and testing new PoE devices such as lighting, displays, or sensors. This display screen allows a user to see and manage the PoE on devices without having to have the full network installed and turned up.

                  So what does it all mean?

                  First Column: This identifies the port numbers, including the two uplink ports 9 and 10

                  Second Column: The power status of the port.  See guide to terms below.

                  Third Column: The entering data rate from the device used on the port (in Mbps)

                  Fourth Column: The exiting data rate from the device (in Mbps)

                  If the data rate turns red, then the port is exceeding its bandwidth settings.

                  PB: The maximum power available on the switch

                  TP: The current output power of the entire switch

                  PD: The number of powered devices connected to the switch

                  Norm: The switch configuration mode.

                  Options: (Norm – Normal switch; VLAN – All ports have their own VLAN; CCTV – CCTV camera set up.  See section on Menu item 1 Switch Mode)

                  What Do the Codes In Column 1 Mean?

                  —-W: Nothing is drawing power on this port
                  OLP: Over load protection has triggered on this port, meaning you device is drawing too much power for the port (see section on Port Power).
                  ULP: Under load protection has triggered on this port, meaning the device is drawing too little power to keep the PoE live on the port.
                  SCP: Short Circuit Protection, meaning the device or the cable connected to this port has short circuited. You’ll need to replace somethings.
                  OFF: When green or white, the port has been set to “off” in the settings
                  When red, the data rate used by this port exceeds the set max. If this happens 10 times in 1 hour, the port will power down to protect the switch and other devices.

                  Switch Bandwidth

                  Switch Bandwidth allows you to limit how much of the switch’s bandwidth a particular port can use.  Let’s say you’re worried some guy will mine crypto currency through this switch.  You can set the switch to alert you here that a single port is taking more bandwidth than the setting.

                  PD Type

                  PD Type gives you control to override the Powered Device negotiation on the switch.
                  • Standard: Your devices will negotiate the type of PoE and the classification
                  • Enhance: Regardless of the device negotiation, this setting allows the port to deliver up to AT power and the settings you put in the PSE Port Power
                  • Legacy: Not used very frequently, this allows the switch to negotiate with a capacitance tag Powered Device
                  Unless you have a specific application or some unusual devices, you’ll likely just keep it on Standard.

                  PD Alive

                  PD Alive lets you set up an automatic reboot function for a port. Let’s say you have a security camera on the port, and it stops communicating for whatever reason. This feature here allows the PoE switch to take over and reboot the port to see if the device will come back on.

                  Use the up and down arrows to navigate to the port you want to have this feature on. Press “Enter” until the “Disable” is green. Then, press “Up” or “Down” until you see “Enable”.

                  Then press “Enter” again to set up the Start Up time using the up/down buttons: how long in seconds the device should take to start up.

                   

                  Then “Enter” again to set the Interval time using the up/down buttons: how long in seconds the switch should wait to see if the device comes back up again.

                  Then “Enter” one last time to set the PowerOff time using the up/down bottons: how long it should stay off when it turns off.

                  When you’re done, use the “Back” button multiple times to exit to the main menu.

                  PSE Power Fine

                  PSE Power Fine allows you to adjust the residual power output of the ports so they can output more power as long as you have enough Total Power Budget (TB). This is used in some specific applications where you know your devices are riding right at the 25 watt limits of PoE+, say with a PTZ camera or a large Wifi access point (some of the high performance Cisco WAP’s fall into this category if their USB ports are turned on).

                  Depending on your situation you can add 5%, 10%, and 15% to the Power Budget (PB).

                  Use the up and down arrow buttons to select the option preferred, then use the “Enter” button to select it.  When the < is next to the setting and green, your option is selected.  “Back” out to the main menu.

                  PSE Port Priority

                  PSE Port Priority sets the priority for which ports will pull more power if the Power Budget (PB) of all the ports exceeds the Total Power Budget (TB) at any time.

                  Let’s say you have security cameras, phones, and wifi access points on your switch, and you’re right at the TB of the switch. If you want to make sure your security cameras stay live even if one of the wifi access points start to draw too much power, then the switch will prioritize the ports based on these settings.

                  By default, the lower number ports (1, 2, 3 . . . ) are higher priority. If you set both ports 1 and 2 at “High” priority, then port 1 will prioritize over port 2 in case of a conflict.

                  With the port numbers highlighted green, use the up and down buttons to select the port number.  Select “Enter”.  Then, use the up and down buttons to select the priority.  You have selected one when it is green and has the < next to is.  Then “Back” to the main menu.

                  PSE Port Enable

                  PSE Port Enable give you the control to be able to turn on and off the power on any port. This ideal for infrastructure or IOT situations where the network may not be turned up for some time but the devices need to be installed, powered on, and tested during installation.

                  With the port number green, use the up and down buttons to select a port number. Then, press “Enter”. Use the up and down buttons until the “Enable” or “Disable” is green. Then press enter.

                  “Back” to the main menu.

                  PSE Port Power

                  PSE Port Power gives you control of whether a port can run at higher power than the traditional PoE standard. For example, you have a Thinlabs all-in-one PoE computer that you know you’ll use hard and add a lot of USB devices to. Rather than worry about your power budget, you can increase your power limit all the way up to 36 watts. Or, if you know your device will be small and you want to save on your PB, you can set the power consumption as low as 2 watts.

                  As before, while the port number is green, use the up and down buttons to select a port. Then press “Enter”. With the power green, use the up and down arrows to set the power limit on the port. “Back” to the main menu.

                  Note: This function is different from the PSE Power Fine function because that sets the fine auto adjustments, while PSE Port Power lets you set the big ranges.

                  In order to take full advantage of the PSE Port Power feature, you need to make sure the switch is set to “Enhanced” on the PD Type menu.  Otherwise you’ll receive this error.

                  LCD On/Off

                  LCD ON/OFF gives you control over how long the LCD screen will remain active after the last use.

                  Simply use the up and down buttons to select your setting, then press “Enter”. The selected setting will turn green and be immediately ready to use. Press “Back” to get to the main menu.

                  Fan Control

                  Fan Control gives you control of when the cooling fans will turn on. It’s based on the percent of the Power Budget (PB) used at the time. This allows you to keep the switch quiet until heat demands force it on.

                  Caution, though, setting the value too high in a warm environment like a packed server rack could allow the switch to go above the rated temperature limits.

                  Simply use the up and down buttons to select your setting, then press “Enter”. The selected setting will turn green and be immediately ready to use. Press “Back” to get to the main menu.

                  Language

                  You can select your Language on this menu.  Currently, Chinese and English are available.  Other languages can be added by request.

                  Simply use the up and down buttons to select your setting, then press “Enter”.  The selected setting will turn green and be immediately ready to use.  Press “Back” to get to the main menu.

                  Default Setting

                  DEFAULT SETTING restores the switch to factory default settings.  

                  Simply use the up and down buttons to select “Confirm”, then press “Enter”.  The selected setting will turn green and be immediately ready to use.  Press “Back” to get to the main menu.

                  About

                  The About menu gives you diagnostic information about model and software version of your device.

                  Technical Specifications

                  AC Plug Connector Type C14
                  Adapters included Yes
                  Cable connector length 3 ft
                  Certifications CE, FCC,
                  Data + PoE Ports 8
                  Data Ports 4 – 2 Gigabit and 2 SPF
                  Data Rate Gigabit
                  Dimensions 17.32″ x 9.133″ x 1.77″ in.
                  Display Type Bright LCD
                  Input Voltage Range 120 / 220 VAC
                  LEDs Per Port 1 – Connections and activity
                  Max Power for Kit 120 watts
                  Mount Type wall and rack (accessories included)
                  Operating Humidity 10% to 90%
                  Operating Temperature Range 0 – 40 C
                  Output Voltage 55 volts
                  PoE Method IEEE 802.3af; IEEE 802.3at
                  PoE Mode/Pinout Mode A (-1,2 +3,6)/Mode B (+4,5 -7,8)
                  PoE Standards Supported IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3az, IEEE802.3x IEEE802.3af, IEEE802.3at

                  If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!