BT-1-WM, BT-1-56V120W, BT-3-56V240W, BT-6-56V480W
Welcome to the PoE Texas Manual for the BT-1-WM, BT-1-56V240W, and BT-1-56V480W that cost-effectively upgrades any non-PoE or PoE port to IEEE 802.3bt and 95 watts!
The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new Power Over Ethernet Midspan.
Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at service@poetexas.com. Phone +1-512-479-0317.
Or you’re always welcome to leave questions or comments on our product pages: BT-1-56V120W, BT-3-56V240W, BT-6-56V480W
You can also download our Product Spec Sheet here.
What’s Inside
BT-1-WM
PARTS LIST:
- 1 X Midspan Injector
- Din Rail Mounting Brackets
Additional items you’ll need not included:
1 – DIN rail
2 – Patch cables to the switch and home run cables to the device
3 – Network Switch
BT-1-56v120w
PARTS LIST:
- 1 X Midspan Injector
- Din Rail Mounting Bracket and Screws
- 56V 120W Power Supply
Additional items you’ll need not included:
1 – DIN rail
2 – Patch cables to the switch and home run cables to the device
3- Network Switch
BT-3-56V240W
PARTS LIST:
- 1 X Midspan Injector
- Din Rail Mounting Bracket and Screws
- 1 X 56V 240W Power Supply
- 1 X 3 Pronged AC Cable
Additional items you’ll need not included:
1 – Patch cables to the switch and home run cables to the device
2 – Network Switch
BT-1-56V480W
PARTS LIST:
- 1 X Midspan Injector
- Din Rail Mounting Bracket and Screws
- 1 X 56V 480W Power Supply
- 1 X 3 Pronged AC Cable
Additional items you’ll need not included:
1 – Patch cables to the switch and home run cables to the device
2 – Network Switch
General Installation
A midspan like the BT-1-WM and it’s kit variations are simple to add on to a network port, and the purpose is to add PoE using a wide range of input power to any network.
With this DIN rail-mounted device, simply mount it on a DIN rail near the networking switch you’d like to pair it with. Then, using a short Ethernet patch cable from the switch’s data port to the LAN port on the PoE midspan. Then the POE port adjacent to the LAN port will now have that IEEE 802.3bt (95 watts) power budget and up to gigabit pass through data. Finally, connect the DC power supply to the Phoenix style connector on the top.
The BT-1-WM is also surge protected, so, while it cannot be mounted outdoors by itself, you can connect it to outdoor devices with confidence. In order to make the surge protection fully functional, you will need to properly ground the connector on the side of the device.
Not sure what grounding is? Panduit has some great graphics around grounding.
CONFIGURATION
There is no configuration necessary with this device. Simply plug it in.
- The green LED indicates power on and drawing less than 30 watts. If the light turns blue, it indicates the port is drawing more than 30 watts of power.
- If the green light begins to blink at any time, it could indicate there is a short in the circuit or a compatibility issue.
STEPS TO TROUBLESHOOT:
1 – At the injector, disconnect the PoE port from your device. Use a PoE Tester to confirm the device is able to power on using a short jumper cable.
2 – At the other end of the network cable to your device, disconnect the device and use the PoE Tester to confirm it is able to negotiate PoE.
3 – Connect the PoE Tester to the end device to monitor power consumption.
If you’re able to power on the device with the PoE Tester inline, it’s likely a compatibility issue. Please contact us at service@poetexas.com to find you the right solution.
Technical Specifications
Product Specifications
| AC Plug Connector Type | C14 |
| Adapter length | 3 ft |
| Certifications | UL/CE/FCC |
| Data + PoE Ports | 1 |
| Data Ports | 1 |
| Data Rate | Gigabit |
| Dimensions | 6KV Model – 214mm x 134 mm x 41 mm |
| Display Type | LED – Green (802.3at) ; Blue (802.3bt) |
| IEC Protection Class | IP 40 |
| Input Frequency Range | 50/60 Hz |
| Input voltage | 100 – 240 VAC |
| Load Regulation | 6KV Surge Protection on Select model as indicated |
| Max Current | 1.72 Amps |
| Max Power for Kit | 95 Watts |
| Max Voltage | 56 volts |
| Max. Amps Per Port | 1.72 Amps |
| Mount Type | Wall |
| Operating Humidity | 20% to 80% |
| Operating Temperature Range | 0 – 40C |
| Output Voltage | 56 volts |
| PoE Method | IEEE 802.3af, IEEE 802.3at, IEEE 802.3bt |
| PoE Mode/Pinout | Mode A (-1,2 +3,6)/Mode B (+4,5 -7,8) |