BT-USBC-A-PD – The PoE Convert for USB-C Laptops and Tablets with a USB-A Port for Accessories
Welcome to the PoE Texas Manual for the patent pending BT-USBC-A-PD that gives you wired Power and Data for your USB Type C laptop plus two USB-A ports for an additional accessories!
The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new Power Over Ethernet Converter.
Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at firstname.lastname@example.org. Phone +1-512-479-0317.
Or you’re always welcome to leave questions or comments on our product page: BT-USBC-A-PD
Your new PoE converter is designed to be simple to install and set up. It has wings to allow the unit to be attached to a desk or wall..
Once it is in place, simply follow these steps in order:
1 – Plug the RJ-45 end into an IEEE 802.3bt PoE (POE++) or 48-56 volt 4Pair passive Power Sourcing Equipment (PSE) with a data source
2 – Ensure the device you’re connecting to is on and logged in
3 – Plug the USB-C connector into the device
The converter will automatically set up the network connection with your device and begin charging. To confirm that, go to the General settings tab or look for the <…> symbol next to Ethernet.
* Please use the provided spacer clamp to avoid damage to the USB-C connector which will void the product warranty.
Configuring Your BT-USBC-A-PD
You’re not required to do any configuration with IEEE 802.3bt switches and injectors. The PoE++ to USBC converter will connect to the PoE switch, negotiate the USB-C power delivery profile, and begin transmitting data.
Not sure what kind of PoE your network switch provides? You can use the LED’s on the side of the device to see what type of PoE power your switch has negotiated with the BT-USBC-A-PD.
Some previous version Cisco uPoE switches do require some configuration on the switch to enable the right PoE for the BT-USBC-A-PD.
Or here are the steps you take after you’ve logged into the terminal.
Switch# configure terminal
Switch(config)# interface gigabitethernet2/0/1
Switch(config-if)# power inline port 2-event
You can still set up your iPad to not automatically lock on a timer. When the screen locks if you would like the screen always on.
- Go to the Settings icon on your iPad
- Select Display & Brightness
- Select Auto Lock
- Set the limit to Never
The splitter will auto-configure the IP settings to default as soon as you connect it up including Dynamic IP addressing.
- Navigate to General Settings, then you’ll see a symbol for the LAN <…>
- Select this and you’ll see the option for PoE Texas LAN, select it
You’ll see your IPV4 IP address information. If it shows “Automatic”, that means your getting a dynamically assigned IP address.
If you’d like to reconfigure the IP address, DNS, and HTTP Proxy settings, you can do that by selecting these options.
The most used option will be fixing your IP address by selecting the “Automatic” button.
For the other networks settings, we’d recommend talking to a service provider or give us a call: 512-479-0317 or email@example.com.
|Adapters included||USB-C to USB-C Right Angle Bi-directional cable|
|Data Rate||(Input) 10/100/1000 Gigabit / (Output) 10/100 Mbps|
|Data Standard||USB 2.0 (Output)|
|LEDs Per Port||Green (POE) / Yellow (USB-C) / Blue (PoE Classification)|
|Max Power for Kit||65 Watts|
|Mount Type||Wall or DIN rail (sold separately)|
|Operating Humidity||-10 – 60C|
|PoE Method||IEEE 802.3bt|
|PoE Standard||IEEE 802.3bt|
|PoE Standards Supported||USB-C PD|
|Power Input||72 watts|
|Power Output||5 volt 3 amp | 9 volt 3 amp | 12 volt 3 amp | 15 volt 2.6 amp | 20 volt 3.25 amp|